鐵藝大門固然好看，固然結實，固然很。但是如果表面處理不好，時間長鐵藝大門表面就會上銹，那么如何保持鐵藝大門的表面美觀度呢，如何處理鐵藝大門的表面呢？下面我給大家介紹一下：

The wrought iron gate is certainly beautiful, sturdy, and noble. But if the surface treatment is not good, the surface of the wrought iron gate will rust over time. So how to maintain the aesthetic appearance of the wrought iron gate and how to treat the surface of the wrought iron gate? Below, I will introduce to you:

鐵藝大門材料堅固，類型多種多樣.風格各異，而且莊重、豪華。鐵藝大門的顏色一般有黑色和古銅色。鐵藝大門用的材料有方管、鍛打方管、方鋼、矩形管、鍛打矩形管、鍛打方鋼、圓鋼、扁鐵、鍛打扁鐵、鐵板、瑪鋼件、沖壓件、門軸等。

The iron gate material is sturdy, with a variety of types and styles, and is solemn and luxurious. The colors of wrought iron gates are generally black and bronze. The materials used for wrought iron gates include square tubes, forged square tubes, square steel, rectangular tubes, forged rectangular tubes, forged square steel, round steel, flat iron, forged flat iron, iron plates, Ma steel parts, stamped parts, door shafts, etc.

一、焊渣 大門的焊接部位較多，必須認真每個焊接部位的焊渣。先用板銼或扁鐵敲打除渣，然后用磨光機和砂布打磨焊縫，使其平滑。對飛濺到其他部位的焊渣也要順勢干凈。

1、 There are many welding parts of the gate for removing welding slag, and it is necessary to carefully remove the welding slag from each welding part. First, use a board file or flat iron to remove slag, and then use a polishing machine and sandpaper to polish the weld seam to make it smooth. The welding slag that splashes onto other parts should also be cleaned up in a timely manner.

二、涂抹原子灰 用原子灰加固化劑(比例50:1)攪拌均勻，涂抹在焊接部位.處理焊縫缺陷。

2、 Apply atomic ash with a curing agent (50:1 ratio) and stir evenly. Apply it to the welding area to treat weld defects.

三、打磨原子灰 干透后，用磨光機和砂布打磨大門的各個組件，尤其是涂抹原子灰的部位更要磨光。

3、 After the atomic ash is completely dried, use a polishing machine and sanding cloth to thoroughly polish all components of the gate, especially the parts coated with atomic ash.

四、噴漆 噴漆前，用濕布擦凈大門的各個部位，不能留有灰塵等。道噴防銹漆，漆膜干透后噴第二道黑漆，噴一道清漆。注意不能有漏噴部位，也不能產生流掛等缺陷。個別細微處可用刷子刷涂補漆。

4、 Before painting, use a damp cloth to thoroughly clean all parts of the door without leaving any dust or debris. The first coat is anti rust paint, the second coat is black paint after the paint film is dry, and the last coat is clear paint. Be careful not to have any areas of leakage or defects such as sagging. Individual small details can be brushed and repainted with a brush.